Skip to content

Special Promo · FREE LDS Cat Eye Gel on $50+ · Nov 16–22 · auto applied - Exclusions apply

DRILL BITS & SANDING BAND - DTK Nail Supply

Nail Drill Bits & Sanding Bands | Carbide, Diamond & Ceramic Bits

Nail drill bits at DTK Nail Supply: 100+ e-file bits on the standard 3/32" shank, from fine to 4XC grit — carbide barrel, tapered and safety bits, 5-in-1, volcano and tornado removal bits, low-heat ceramic bits, diamond cuticle bits and under-nail cleaners — plus 3- to 6-piece bit sets from $35, LAVIS and Medicool sanding bands and rubber mandrels. Free U.S. shipping on orders over $75.

Learn More About This Collection

What you will find in this drill bit collection

This page holds the e-file bits, sanding mandrels and sanding bands we stock for salon and home-studio drills. Every bit and mandrel here uses the standard 3/32 inch shank, the size that fits the collet of a professional nail e-file, so one drill can run the whole lineup. The bits come in three materials: carbide for cutting product, ceramic for gentler filing, and diamond for cuticle and natural nail detail. Most carbide and ceramic shapes are offered in several grits, from fine (F) up to double extra coarse (2XC), and a few go further.

Many bits appear twice in the grid: once as a single listing for one grit, and once as a combined listing where you pick the grit from a drop-down. Both lead to the same bit. Use the filters beside the grid to narrow by availability or price, or read the guide below to work out which shape and grit you need before you browse.

How to read a drill bit name

Each listing title carries four pieces of information, and once you can read them the grid becomes much easier to scan.

  • Material: carbide, ceramic or diamond. This decides how fast the bit cuts and what it should touch.
  • Barrel size: small barrel bits reach tighter areas such as sidewalls; large barrel bits cover more surface per pass.
  • Shape and top: a smooth top (safety) bit has a rounded, uncut end so it does not nick the skin near the cuticle; a flat top bit has a sharp cutting edge for shortening and shaping; tapered, flame, conical, ball, tornado and volcano bits each suit a specific area or task.
  • Grit: the letters at the end of the name, explained below.

The grit ladder runs F (fine), M (medium), C (coarse), XC (extra coarse) and 2XC (double extra coarse). The dust-proof line adds 3XC, the blue carbide bit goes to 4XC, and two super long 5-in-1 bits pair a coarse cutting section with a 3XF (extra fine) finishing section. Fine grits refine and lightly buff; the coarse end is for removing bulk acrylic, hard gel, poly gel and dip powder. The XC and 2XC grits are made for intermediate to professional techs.

Bit families compared

FamilyMaterialGrits stockedMain job
Small and large barrel, smooth top safetyCarbideF to 2XCRefining and removal close to the cuticle without nicking it
Small and large barrel, flat topCarbideF to 2XCShortening, shaping and bulk removal; keep the sharp edge away from skin
Small and large barrel, taperedCarbideF to 2XC (large), F to C (small)Sidewalls, cuticle area and shaping thicker enhancements
5-in-1 (silver, purple, multicolor)CarbideF, M, CCleaning, shaping, shortening, cuticle work and backfills with one bit
Tornado and volcanoCarbideM to 2XCFast filing of acrylic, builder gel and dip; the volcano has a rounded top
Super long 5-in-1CarbideF to 2XC, plus XC+3XF and 2XC+3XFRefining to heavy removal; the Pro versions add a finishing grit
Barrel, flame and 5-in-1CeramicF, M, CGel polish removal and refining with less heat build-up
Ball, spiral, nib, safety, small cylinder, barrelDiamondSingle grit per shapeCuticle cleaning, lifting dead skin and natural nail detail
Conical and under-nail cleanerCarbide or ceramicMedium (conical), single grit (UNC)Cleaning around the cuticle and under the free edge
Sanding mandrelsRubber bodyTakes disposable bands, such as #80 and #240Holding single-use sanding bands

Which bit for which job

  • Cuticle prep and dead skin: a diamond ball, spiral, nib or safety bit, or a carbide conical bit in medium grit. These are built to lift dead cuticle from the nail plate with control.
  • Gel polish removal: a medium carbide smooth top bit, a ceramic barrel or ceramic 5-in-1 in medium, or the dust-proof bit in fine or medium.
  • Bulk acrylic, hard gel, poly gel and dip: carbide in coarse to 2XC, such as the flat top barrels, tornado, volcano or super long 5-in-1. The blue 4XC bit is for the heaviest removal on thick sets.
  • Refining and shaping enhancements: medium grit tapered or barrel bits, then a fine bit or a fine sanding band to finish the surface.
  • Sidewalls and tight areas: small barrel and tapered bits reach where a large barrel cannot.
  • Under the free edge: the carbide or ceramic under-nail cleaner (UNC) bit.
  • Left-handed techs: the carbide 5-in-1 and the diamond spiral are made for two-way rotation, so they cut in forward and reverse.

Carbide, ceramic or diamond

Carbide is the workhorse material for enhancements. It cuts acrylic, builder gel and dip quickly and comes in the widest choice of shapes and grits on this page. Because flat top carbide bits have a sharp cutting edge, use them with care near the skin; the smooth top versions exist for exactly that zone.

Ceramic bits keep heat build-up low, which makes filing more comfortable for the client. They are a good fit for gel polish removal, light refinement of natural nails and refining builder gel.

Diamond bits carry a diamond-coated surface for controlled, gentle abrasion. Use them for cuticle work, light buffing and shaping of natural nails, and detail prep before enhancements. The natural nail buffer bit in this group smooths ridges on the nail surface.

Many techs keep one of each: a carbide bit for removal, a ceramic bit for gel polish, and a diamond bit for the cuticle area.

Within carbide, the shape changes how a bit behaves. Tornado bits carry a spiral cut for fast, aggressive filing on acrylic and builder gel. Volcano bits have a rounded top for refining enhancements with precision and control. The 5-in-1 bits combine cleaning, shaping, shortening, cuticle work and under-nail or backfill work in one tool. The dust-proof bits are cut to keep filing dust down while removing gel polish and soft gel.

Sanding bits, mandrels and bands

A sanding bit is a rubber mandrel on a 3/32 inch shank that holds a disposable sanding band. You slide a fresh band on for each client and keep the mandrel. We stock the standard mandrel, a large 7 mm rubber mandrel that grips bands firmly, and a small mandrel for detail sanding near the cuticle and sidewalls.

BandGritPackUse
LAVIS pink sanding band, coarse#80Multi-packFast removal of acrylic and builder gel
LAVIS pink sanding band, fine#240Multi-packRemoving shine before gel and finishing surfaces
Medicool white sanding band, coarse#80Box of 100Heavy removal in a busy salon

Speed matters with bands. Run fine bands at the slow end of your e-file's range for natural nails and the cuticle area. Medium bands handle quick prep, shaping acrylic and backfills. Coarse bands remove product fast; run them at medium speed and smooth any sharp edges with a hand file. Coarse grits also create more airborne dust, so pair them with a mask and a dust collector.

Using a drill bit safely

  1. Seat the bit: push the 3/32 inch shank fully into the collet and lock the chuck before you start the drill.
  2. Start slow: begin at a low speed and raise it only as the task needs. For e-file cuticle cleanup, stay around 5,000 to 8,000 RPM; too much speed overheats the nail plate.
  3. Hold the angle: keep the bit at a slight angle with its flat side on the product. Never point it straight down into the nail, and avoid working with the tip.
  4. Stay on product: aim the bit at gel, acrylic or dip, never into the nail bed, and move in light, steady passes without pressing.
  5. Match grit to layer: step down from coarse to medium to fine as you get closer to the natural nail.
  6. Finish by hand: smooth edges with a file and buffer, then move on to prep.

New techs and home users get the most control from smooth top safety bits and fine or medium grits; leave XC and above until your hand is steady.

Cleaning and storing your bits

  • Clean and sanitize each bit between clients, following your state board rules for reusable implements.
  • Sanding bands are single-use: pop the band off the mandrel after each client and fit a fresh one.
  • Store bits dry, in a closed case or bit holder, so the cutting surfaces do not knock against each other.
  • Keep the matching mandrel and a stock of bands together, so a fresh band is always ready at the station.

Kits and building a bit lineup

If you are setting up a station, the 3, 4, 5 and 6-piece kits put a mixed set of 3/32 inch bits in one box for everyday filing; the larger kits add cuticle, sidewall and detail work. Working techs often build their own lineup from single bits instead: one coarse carbide for removal, one medium bit for refining, one fine or ceramic bit for gel polish, a diamond cuticle bit, and a mandrel with bands. Prices are listed on each product page.

The drills themselves live in nail drills and e-files, and a portable dust collector keeps filing dust off the table.

Related collections

Related reads

115 products

6-Piece Advanced Artist Kit - Tools & Accessories

Regular price $63.00
Sale price Regular price

3-Piece Essentials Kit (Minimal but Mighty)

Regular price $35.00
Sale price Regular price

Lavis Pink Sanding Bands - Coarse Sand #80

Regular price
Sale price $9.99 Regular price $11.67

#93 Drill Bits NEEDLE - Tools & Accessories

Regular price $10.50
Sale price Regular price

#64 Ceramic Under Nail Cleaner

Regular price $12.00
Sale price Regular price

Carbide Large Barrel Smooth Top Safety Bit

Regular price $10.50
Sale price Regular price

Carbide Small Barrel Flat Top Drill Bit

Regular price $10.50
Sale price Regular price

Carbide Large Barrel Flat Top Drill Bit

Regular price $10.50
Sale price Regular price

Carbide 5in1 Drill Bit Silver - Tools & Accessories

Regular price $14.00
Sale price Regular price

Carbide 5in1 Drill Bit Purple - Tools & Accessories

Regular price $14.00
Sale price Regular price

Carbide Tornado Drill Bit - Tools & Accessories

Regular price $14.00
Sale price Regular price

Carbide Volcano Drill Bit - Tools & Accessories

Regular price $14.00
Sale price Regular price

Carbide Conical Drill Bit - Tools & Accessories

Regular price $10.50
Sale price Regular price

Diamond Cuticle Ball Drill Bit

Regular price $7.50
Sale price Regular price

Ceramic 5in1 Drill Bit - Tools & Accessories

Regular price $12.00
Sale price Regular price

Ceramic Large Barrel Smooth Top Safety Bit

Regular price $12.00
Sale price Regular price

Ceramic Large Barrel Flat Top Drill Bit

Regular price $12.00
Sale price Regular price

Ceramic Flame Drill Bit - Tools & Accessories

Regular price $12.00
Sale price Regular price

Super Long 5in1 Bit - Tools & Accessories

Regular price $15.00
Sale price Regular price

Super Long 5in1 Bit Pro - Tools & Accessories

Regular price $15.00
Sale price Regular price

#71 3/32" Dust Proof Bit F - Tools & Accessories

Regular price $15.00
Sale price Regular price

#05 Carbide Small Barrel Smooth Top Safety Bit 2XC

Regular price $10.50
Sale price Regular price

#06 Carbide Large Barrel Smooth Top Safety Bit F

Regular price $10.50
Sale price Regular price

#14 Carbide Small Barrel Flat Top Drill Bit XC

Regular price $10.50
Sale price Regular price

#16 Carbide Large Barrel Flat Top Drill Bit F

Regular price $10.50
Sale price Regular price

#19 Carbide Large Barrel Flat Top Drill Bit XC

Regular price $10.50
Sale price Regular price

#20 Carbide Large Barrel Flat Top Drill Bit 2XC

Regular price $10.50
Sale price Regular price

#23 Carbide Small Barrel Tapered Drill Bit C

Regular price $10.50
Sale price Regular price

#24 Carbide Large Barrel Tapered Drill Bit F

Regular price $10.50
Sale price Regular price

#35 Carbide 5in1 Drill Bit Multilcolor F

Regular price $14.00
Sale price Regular price

#37 Carbide 5in1 Drill Bit Multilcolor C

Regular price $14.00
Sale price Regular price

#39 Carbide Turnado Drill Bit C

Regular price $14.00
Sale price Regular price

#41 Carbide Turnado Drill Bit 2XC

Regular price $14.00
Sale price Regular price

Frequently Asked Questions

What shank size are these nail drill bits?+

Every bit and sanding mandrel on this page uses the standard 3/32 inch shank, the size that fits the collet of a professional nail e-file. Push the shank fully into the collet and lock the chuck before you turn the drill on, then start at a low speed and raise it only as far as the task needs.

What do the grit letters F, M, C, XC and 2XC mean?+

They run from fine to double extra coarse. Fine bits refine and lightly buff, medium bits refine thicker layers and remove gel polish, and coarse to 2XC bits remove bulk acrylic, hard gel, poly gel and dip powder. The dust-proof line adds 3XC, the blue carbide bit reaches 4XC, and XC and above are made for intermediate to professional techs.

Should I choose carbide, ceramic or diamond bits?+

Carbide cuts enhancements fastest and comes in the most shapes and grits. Ceramic keeps heat build-up low, which suits gel polish removal and refining builder gel. Diamond bits give gentle, controlled abrasion for cuticle work and natural nail detail. Many techs keep one of each for removal, gel polish and the cuticle area, and switch bits as the service moves from one stage to the next.

How do sanding bands and mandrels work?+

A sanding bit is a rubber mandrel on a 3/32 inch shank. Slide a disposable band over the rubber body, use it for one client, then pop it off and fit a fresh one while keeping the mandrel. Run fine bands slowly on natural nails, and coarse bands at medium speed for fast product removal, finishing sharp edges with a hand file.

Which bits are best for a beginner?+

Start with a smooth top safety bit in fine or medium grit, because its rounded end will not nick the skin near the cuticle, plus a diamond cuticle bit and a mandrel with fine bands. Begin at a low speed, keep the bit at a slight angle on the product, and never point it straight into the nail. Leave XC and coarser grits until your hand control is steady.